The fluid in the pan is not under any pressure so as long as it doesn't leak, and the bolts are tight enough to not get loose, it's fine. As stated above, do check to see if the pan is warped. Worked great, it hasn't leaked and I haven't had to tighten it any more. head bolt torque specs 3 steps first torque to 12.7 to 16.2 second 90degree turn third another 90 degree turn. My thought was that if it isn't tight enough, I snug it some more until it stops leaking. This last time I torqued it by hand till it felt snug, then stopped. If you go back around you will find that the bolts turn a little more, and if you keep doing it you will end up mashing the gasket to the point that it won't seal. I think what happens is when you start to get them to the proper torque, which is 97 inch/pounds or 8 foot/pounds, the gasket has given up some of its resistance to the pressure. I just went thru a similar thing when changing the fluid in my 700R4. First 2 were done by a shop dang another if you want it done right deal. Transmission Oil Pan to Case Bolt 7-10 lb ftĬan someone tell me the torque specs for a 4L60 tranny pan?Heading towards the 3rd gasket. Transmission Oil Cooler Pipe Fitting 26-30 lb ft Transmission Fluid Pressure Manual Valve Position Switch to Valve Body Bolt 6-10 lb ft Trans Mount to Transmission Bolt 18 lb ft TCC Solenoid Assembly to Case Bolt 6-10 lb ft Stud, Automatic Transmission Case Extension (Y-car) 13-16 lb ft Pressure Control Solenoid Bracket to Valve Body Bolt 6-10 lb ft Genuine Mazda Automatic Transmission Oil Pan FN112151XB and Bolts (20Pack) 9YA0-20-627 (Mazda3, 5, 6, Protege) 1999-2009). Plug Assembly, Automatic Transmission Oil Pan (Y) 20.7-23.6 lb ft Plug Assembly, Automatic Transmission Oil Pan (C/K) 22.1-29.5 lb ft Plate to Converter Bolt (Shipping) 20-25 lb ft Plate to Case Bolt (Shipping) 20-25 lb ft Park/Neutral Position Switch Screw 27 lb in Park Brake Bracket to Case Bolt 20-25 lb ft 4-Speed Automatic Transmission for 1.6L 2002 Mazda Protege Remanufactured, and rebuilt Transmissions available. Oil Passage Cover to Case Bolt 6-10 lb ft Oil Pan to Transmission Case Bolt 97 lb in Manual Shaft to Inside Detent Lever Nut 20-25 lb ft Make sure that you put the strength and torque parallel to perpendicular to the plug bolt. lock it tightly around the bolt and remove (pull instead of push). If I may ask, what is wrong with the drain. Heat Shield to Transmission Bolt 13 lb ft Transmission part you need to equip your 2005 Mazda B2300 for continued performance. 2002 Mazda Protege 4 cyl Front Wheel Drive Automatic procedure to replace. It helped me to have my son raise the engine while I watched through the wheel well, to get the height just right.īecause of the tight space to get the mounts in place with the brackets attached, patience is your greatest asset on this job.Well I found this do these numbers sound right 7-10 ft lb? Or is the 97 in lb correct? Do 120 inlbs=10ftlbs?ĤL60-E Transmission Torque Specs ApplicationĪccumulator Cover to Case Bolt 6-10 lb ftĬase Extension to Case Bolt (4WD Shipping) 8.3-16.7 lb ftĬonverter Housing to Case Screw 48-55 lb ftĭetent Spring to Valve Body Bolt 15-20 lb ftįlywheel to Torque Converter Bolt 46 lb ftįorward Accumulator Cover to Valve Body Bolt 6-10 lb ft Once all of the 6 bolts and 2 nuts are removed use a floor jack at the crank pulley to raise the engine just enough to wiggle the mounts in and out from the top. im looking for the cylinder head bolts torque for a 2002 mazda protege with a 2. The MM/Frame nut is reached from the bottom. Mazda Protege: im looking cylinder head bolts torque. I forget which ones, but a couple of the Bracket bolts are different lengths, so pay attention. All 3 of each MM bracket bolts are easily reached through the wheel wells with the proper socket extensions. Rest the car on jack stands at the front Rocker Panel lifting points after removing the front wheels. They transfer a little more vibration but hey, it's a Sports Car.Īs for Removal & Replacement, it's not as difficult as many describe in the YouTube videos. Thus, your Mazda Protege is to consume more fuel because the engine will have to produce more torque. wheel width parameters, and the Mazda Protege bolt pattern that is important for the correct fitment. After being in for 90K miles they are still good. 2002 2001 2000 1999 Mazda Protege Wheel Size 2003 2002 Shop for Tire. I was consistently missing the 2nd to 3rd speed shift. My Motor Mounts were shot, with one being torn at 70K miles of speed shifting.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |